The correct use of lamps and lanterns - Yangzhou Chuang Chuang photoelectric Group Co., Ltd.

大乐透12生肖选号

Contact us Contact

Proper use of lamps and lanterns

2015/4/1 20:05:25 Click:

Before lighting installation, confirm the specifications of lamps and lanterns.
(1)  
Confirm whether the prescribed voltage of the luminaire is in line with the supply voltage, for example: 110V Use of lamps and lanterns 220V The voltage will destroy the inner stabilizer.
(2)  
Fluorescent lamp HID Prescribed voltage in allowable range of lamps and lanterns

A)   If the power supply and voltage are too high, the life of the stabilizer and bulb will be reduced.

B)   The power and voltage are too low, so that the bulb will not light or reduce life. Allowable voltage range of lamps and lanterns

Fluorescent lamp + - 6% within

HID Lamps and lanterns + - 6% within ( But when using the metal lamp again + -5% within )

Two .   Confirmation of selected lamps and lanterns

Lamps and lanterns are suitable for all kinds of places. Suitable environment for lamps and lanterns

Rain place ( Eaves and rain outside the house ) A place where flammable gases are produced by rain proof lamps and lanterns. ( Petroleum and chemical plants ) Pressure and explosion proof luminaire

A damp place ( Bathroom, basement, underpass, etc. ) A place with corrosive gases for damp proof lamps and lanterns. ( Chemical factories and hot springs ) Corrosion resistant lamps and lanterns

Cryogenic sites ( Freezer, etc. ) A place where lamps and lanterns vibrate in refrigerating rooms. ( Factories, gymnasium, etc. ) Shock resistant luminaire

Please use waterproof lamps and lanterns for watertight and damp places outside the bathroom. ( Damp proof type ( Rain proof type ) , ( Rainproof and moisture proof type ) When using, please select lamps suitable for use. Eaves, side roads and other wet places where the rain is wet. The lamps and lanterns are not well insulated due to humidity, and the reflective boards are rusty. Please use damp proof and rain proof lamps.

Three .   Installation of lamps and lanterns

A)   The installation distance between luminaire and luminaire should not be too close. When the lamp installation is too intensive, the temperature of the luminaire will be raised.

B)   The excessive temperature of the luminaire will cause the temperature rise of the stabilizer to exceed the allowable range, resulting in the shortening of the life of the stabilizer and the bulb, the burning and destruction of the inner space of the lamp holder or the luminaire.

C)   The factors that increase the temperature of lamps and lanterns are affected by the size of interior space of lamps and lanterns, the size of lamps and luminaries, and the influence of construction and materials.

(1)   Suitable installation intervals for lamps and lanterns.

(2)   Increase the interior space of lamps and lanterns.

(3)   Heat dissipation holes are arranged around the luminaire body.

(4)   The stabilizer shall be separately installed.

(5)   The ceiling is well ventilated. D)   Installation position of lamps and lanterns avoid contact with flammable articles such as curtains.

E)   The upper part of the gas appliance is very high, and the luminaire should be kept at an appropriate distance from the heat source. For example, the installation position of the luminaire in the kitchen should be from the heat source. One Above meters.

F)   The installation direction of rainproof lamps is in the specified direction and must be installed in the specified direction to prevent rain invasion.

G)   When installing damp proof and rain proof luminaries, we should pay attention to the following points:

(1)   The mounting surface must be tightly attached to the rubber gasket of the lamp installation part.

(2)   If the mounting surface is uneven, the lamps and lanterns should be installed around the installation position of the lamp.

(3)   Pay attention to whether the outlet of the power supply line is flooded.

H)   When the steel reinforced concrete surface is equipped with lamps and lanterns, it is necessary to wait for the concrete surface to be dry before installing the luminaire. If the drying is not confirmed, the moisture of the concrete will be absorbed by the lamp after installation of the luminaire, resulting in the reduction of insulation and the loss of the painting surface. .

567彩票 下载 北斗棋牌全部版本 下载星云娱乐斗地主 乐彩3d论坛手机17500 3d十年研究技巧 南粤风釆36选7最新开奖 中彩网投注为什么不花钱 乐彩网17500双色球出球顺序 S中彩票妙招 5933cc彩票在线